If the jumper is on 2-connector pins and it is held on a single pin, place it on both, wait one second then return it to its original position. When you have access to the motherboard, you need to look for a specific jumper. I tried the Generic Phoenix password on my laptop and it worked! If you choose not to enter a password, one will be automatically generated for you, and it will be sent to you once you've confirmed your subscription. Software reset If the password is only required at setup, it is possible, with specific motherboards, to recover it without having to follow the hardware reset instructions described above. I wonder if there is a cheaper way of doing this? If the jumper is on a 2-connector pins and that is holding on a single pin, place it on both, wait one second and then return it to its original position. Whether you can load the operating system or not depends on how many security settings have been enabled. The biggest challenge is to find this jumper.
This is done by moving a jumper on the motherboard. For example, if pins 1 and 2 are covered, web page you will need to remove it and cover pins 2 and 3. This is a hidden list, which means that the list of members is available only to the list administrator. Not only is it easier to open a desktop, finding the component that needs to be taken out is much easier also. A second option usually called Boot Up Password or something similar has to be enabled in order for you to see a message before the operating system loads. The chip is located on the motherboard. You can subscribe to the list, or change your existing subscription, in the sections below.
Without getting too technical, the reason it worked is because the password generated by the website and my password generate the same checksum. When you move that piece of plastic to cover a different set of pins, it changes the settings on the motherboard. I was wondering how much would it cost for a computer not in warrenty to be it fixed and the bios data put back on? Using CmosPwd To post a message to all the list members, send email to. You can always request a mail-back of your password when you edit your personal options. All you have to do now is go to a website called and simply type in that number! This provides only mild security, but should prevent others from messing with your subscription. About Online Tech Tips Welcome to Online Tech Tips — A blog that provide readers with daily computer tutorials, technology news, software reviews, and personal computing tips.
Once you have changed the jumper setting, go ahead and turn on the computer, check that the password is gone and then turn it off again. On a laptop, you may not see jumpers, but dip switches instead. All you have to do here is move the switch up or down. It is usually close to the battery. Usually, the jumper will consist of three pins with two pins covered.
Do not use a valuable password as it will occasionally be emailed back to you in cleartext. The best place to look is around the edges of the motherboard first. . Subscribing to CmosPwd Subscribe to CmosPwd by filling out the following form. You will be sent email requesting confirmation, to prevent others from gratuitously subscribing you.
Use something like a butter knife or flat head screwdriver to pop the battery out. Both these methods have been described in detail. Touch the chassis of the casing with a metallic object to discharge static electricity. Hi I've just bought a laptop from a friend of mine who hadn't used it for a long time and had forgotten his password. You can then put the jumper back into its original position. Instead of listing them all here, check out this that has a list of all the default passwords.
In that case, move on to the next method. Make sure you turn off your computer completely, disconnect all cables and unplug the power also before doing this. Your email address: Your name optional : You may enter a privacy password below. I ran cmospwd so I could play about with the bios but I ended up wiping it instead. After the third time, I got a message saying System Disabled, but I also got a number displayed right below that message. Pick a password: Reenter password to confirm:. If there are only two pins for the jumper, just remove the cover completely.
A jumper is basically a number of pins sticking out of the motherboard with a small piece of plastic covering some of the pins. If the jumper is on 3-connector pins, place it on the middle and the initially uncovered pins. Two method are described here - hardware reset and software reset. I have all the paperwork. .
. . . . . . .
. . . . .
0 
Star